一、保證自上料混凝土攪拌車水箱中有足夠的水以及減水劑
1、 Ensure that there is enough water and water reducing agent in the tank of concrete mixer truck
一般攪拌機所使用的物料都是比較干燥的,沒有添加水的話是無法正常對物料進行攪拌工作的。因此減水劑以及水在設備操作中的作用還是相當重要的。
Generally, the materials used in the mixer are relatively dry, so it is impossible to mix the materials normally without adding water. Therefore, the role of water reducing agent and water in equipment operation is quite important.
二、確認自上料混凝土攪拌車設備的攪拌罐處于停止的狀態
2、 Confirm that the mixing tank from the loading concrete mixer is in the stop state
由于發動機在啟動時如果攪拌罐正好處于高速旋轉的狀態,這時會對設備減速機帶來一定的損壞,影響設備的正常使用。
When the engine is started, if the mixing tank is in the state of high-speed rotation, it will damage the reducer of the equipment and affect the normal use of the equipment.
三、對設備的各個零件以及配件進行檢查工作,存在問題時可以及時排除
3、 Check the parts and accessories of the equipment, and eliminate the problems in time
1、點火之前先檢查機油、防凍液、潤滑油和冷卻水等,發現不足時,應重新進行添加。
1. Before ignition, check the engine oil, antifreeze, lubricating oil and cooling water, and add them again if they are insufficient.
2、車子啟動后,再讓罐子低速旋轉,圍繞著車檢查輪胎氣壓,是否有漏氣的胎,再用螺絲刀剔掉在胎縫里的石子。
2. After the car starts, let the jar rotate at a low speed. Check the tire pressure around the car to see if there is a flat tire. Then use a screwdriver to remove the stones in the tire seams.
3、再檢查燈光,尤其是腰燈,務必保證照著輪胎邊緣,工地會經常亂堆放鋼筋之類的東西,而胎側是更薄弱的。
3. Check the light again, especially the waist lamp, and make sure to shine on the edge of the tire. The construction site will often pile up reinforcement and other things, and the sidewall is the weakest.
4、用抹布擦干凈兩邊的后視鏡,窗戶玻璃,工地路況復雜,光線不好,視線一定要保證!
4. Clean the rear-view mirror and window glass on both sides with dishcloth. The road conditions on the construction site are complex and the light is not good. The line of sight must be guaranteed first!
一般自上料混凝土攪拌車這種建筑施工設備的操作環境通常都不是很好,這也導致需要我們對設備在操作之前有詳細的了解才行。在確保設備不存在有任何故障問題之后才能夠操作使用設備正常運行,避免在操作中可能存在的各種不良問題。
Generally, the operating environment of self loading concrete mixer is not very good, which also requires us to have a detailed understanding of the equipment before operation. After ensuring that the equipment does not have any fault problems, it can be operated and used normally, so as to avoid all kinds of bad problems that may exist in the operation.
This article is organized and released by the fully automatic feeding mixer. Do you have any understanding of these contents? For more information, please click: http://www.ksmayo.cn We'll have a lot more to see.