In the long-term use of concrete machinery such as automatic feeding mixer, some failures will inevitably occur. At this time, we need to carry out a certain cleaning work on the mechanical soil slag. So let's take a closer look at how to clean up the soil properly.

　　1、準備應急驅動軟管，關閉攪拌車，然后拆下液壓馬達上的高壓油管接頭。

　　1. Prepare the emergency drive hose, close the mixer, and then remove the high pressure oil pipe connector from the hydraulic motor.

　　2、救援車關閉，液壓馬達的高壓油管被拆除，故障車輛上的相應連接器與應急驅動軟管連接。

　　2. The rescue vehicle was closed, the high-pressure oil pipe of the hydraulic motor was removed, and the corresponding connector on the fault vehicle was connected with the emergency drive hose.

　　3、啟動救援車并將其手柄轉到卸貨位置。故障車輛內的混凝土排出。

　　3. Start the rescue truck and turn its handle to the unloading position. Discharge of concrete from the faulty vehicle.

　　4、緊急驅動完成后，拆下驅動軟管并恢復兩輛車的原始狀態。

　　4. After the emergency drive is completed, remove the drive hose and restore the original condition of both vehicles.
                

　　5、在滾輪和滾道之間放置一個木質楔子，以控制攪拌車的旋轉。一定要注意。關閉發動機并拆下液壓馬達的高壓油管。攪拌車可以自由旋轉。

　　5. A wooden wedge is placed between the roller and the raceway to control the rotation of the mixer. Pay attention to safety. Shut down the engine and remove the high pressure oil pipe from the hydraulic motor. The mixer can rotate freely.

　　6、控制攪拌筒的旋轉，將維護孔轉到下部，然后打開維護孔清理缸內的混凝土。這時，一定要注意。混凝土卸料后，恢復原來的樣子。

　　6. Control the rotation of the mixing drum, turn the maintenance hole to the lower part, and then open the maintenance hole to clean the concrete in the cylinder. At this time, be sure to be safe. After the concrete is discharged, the original full-automatic feeding mixer is restored.

　　全自動上料攪拌機主要適用于城市的建設，建筑的施工，是專門用來運輸建筑所需的混凝并且在運輸的過程中始終保持著攪拌的狀態，從而保證混凝土不會凝固。那怎樣能延長其使用壽命呢？

　　Automatic feeding mixer is mainly suitable for urban construction and construction, which is specially used to transport the concrete required by buildings and always keeps mixing state during transportation, so as to ensure that concrete will not set. How to prolong its service life?

　　1、對于新購入的車輛，初度運用50h支配，就該檢查遍地螺栓緊固情況。包括罐體分頭與減速機的連接螺栓，減速機底座與前臺的連接螺栓，拖輪底座與機架的聯接螺栓，以及副梁與大梁的聯接螺栓等。往后要保證每月守時檢查一次。

　　1. For newly purchased vehicles, the initial use of 50h control, it is necessary to check the tightening of bolts everywhere. It includes the connecting bolts between the tank split and the reducer, the connecting bolts between the reducer base and the front desk, the connecting bolts between the tugboat base and the frame, and the connecting bolts between the auxiliary beam and the main beam. In the future, we should make sure to check on time every month.

　　2、液壓系統部件精度較高。尤其是攪拌車液壓泵，養護簡便，但懇求很高。液壓油要守時更換，初度工作500h，往后2000h或起碼每年更換一次，濾芯應當同時更換。加油或換油時，建議機有必要處于終止情況，否則將構成液壓系統損壞。

　　2. The accuracy of hydraulic system components is high. Especially the mixer hydraulic pump, maintenance is simple, but the appeal is very high. The hydraulic oil should be replaced on time. The initial working time is 500h, and the next 2000h or at least once a year. The filter element should be replaced at the same time. When refueling or changing oil, it is suggested that the machine should be in the termination condition, otherwise the hydraulic system will be damaged.

　　3、天天行車前檢查拖輪與滾道的聯絡面潤滑油是不是干澀，應及時補償，堅持杰出的潤滑作用。每次在車輛建議之前，檢查冷卻器和減速機的油位，保證油位指示在目視范圍內；檢查液壓油路的密封情況，堅 持液壓系統清潔和密封，防止塵粒和水份等污染系統液壓油，構成系統不能正常工作或損壞。起碼每月一次整理拖輪和滾道上的污物；經過拖輪上的油嘴，向拖輪寫入潤滑油脂。保證轉動軸起碼每月潤滑一次。

　　3. Check whether the lubricating oil on the contact surface of tugboat and raceway is dry and astringent before driving every day. It should be compensated in time and adhere to the outstanding lubrication function. Check the oil level of cooler and reducer to ensure that the oil level indication is within the visual range before the vehicle proposal; check the sealing condition of the hydraulic oil circuit, adhere to the cleaning and sealing of the hydraulic system, and prevent dust particles and water from polluting the hydraulic oil of the system, causing the system to fail to work normally or be damaged. Clean up the dirt on the tugboat and raceway at least once a month; write grease to the tug through the nozzle on the tug. Ensure that the rotating shaft is lubricated at least once a month.

　　4、制止對水箱隨意焊接和改動，防止重物碰擊；水位顯現管和濾網應及時更換，防止堵塞，影響誰為分區；常常檢查各種閥體是不是堵塞或是不是又工作失常，并及時進行潤滑；在有結冰或許的環境中運用。

　　4. It is forbidden to weld and change the water tank at will to prevent heavy objects from hitting; the water level display pipe and filter screen should be replaced in time to prevent blockage and affect the partition; various valve bodies should be often checked for blockage or abnormal operation, and lubrication should be carried out in time; it should be used in the environment with icing.

　　以上是關于全自動上料攪拌機清理殘渣及延長使用壽命的詳細介紹，感謝您的閱讀，希望對您有所幫助，如您想要了解更多內容歡迎點擊我們的官網http://www.ksmayo.cn首頁。

　　The above is a detailed introduction about cleaning residue and prolonging service life of automatic feeding mixer. Thank you for your reading and hope to help you. If you want to know more, please click our official website http://www.ksmayo.cn Home page.