久久综合给合久久狠狠狠97色69,国产欧美在线观看不卡,少妇高潮流白浆在线观看,亚洲熟女精品中文字幕

山東山汽工程機械（集團）有限公司
熱線電話：400-879-1999 山汽微信
鄭重聲明 購機 售后
在線詢價
熱線電話：400-879-1999
您現在所在的位置: 首頁> 新聞資訊 > 公司新聞

自動上料攪拌機在運輸中應該注意什么？

所屬分類：公司新聞 發布時間：2020-12-10 來源：http://www.ksmayo.cn 瀏覽量：0

1、蓄電池的保養檢查：檢查蓄電池固定是否牢固。
1. Battery maintenance inspection: check whether the battery is fixed firmly.
2、輪胎的檢查：每月應在常溫下檢查一下輪胎氣壓。
2. Tire inspection: check the tire pressure at room temperature every month.
3、離合器總泵液面的檢查：離合器液面介于高、低液面間則表示正常，如果低于標準線，則可能是總泵或分泵皮碗損壞。
3. Inspection of clutch master cylinder liquid level: if the clutch liquid level is between high and low, it means that it is normal. If it is lower than the standard line, it may be that the master cylinder or the cylinder cup is damaged.
4、制動液面的檢查：制動也在高、低位之間則表示正常。
4. Check the brake fluid level: if the brake is between high and low, it means normal.
5、發動機冷卻液液面檢查：發動機在熱機狀態時，千萬不要打開散熱器蓋，否則可能會被濺出的冷卻液或高溫蒸氣燙傷。等發動機冷卻后，檢查冷卻液的液面應處于滿位和低位之間，否則應加蒸餾水或純凈水或冷凍液，加水后的液面高度不能超過滿位。如發現短時間內冷卻液減少的很快攪拌，自動上料攪拌車檢查步驟應檢查冷卻系統是否有泄漏或到維修站去檢查。
全自動上料攪拌車
5. Check the engine coolant level: when the engine is in hot state, do not open the radiator cap, otherwise it may be scalded by the splashed coolant or high temperature steam. After the engine cools down, check that the coolant level should be between the full level and the low level. Otherwise, distilled water or pure water or refrigerant should be added. The liquid level after adding water should not exceed the full level. If it is found that the coolant decreases rapidly in a short period of time, the automatic feeding mixer should check whether there is leakage in the cooling system or go to the maintenance station for inspection.
自動上料攪拌機操作環境通常都不是很好，這也導致需要我們對設備在操作之前有詳細的了解才行。在確保設備不存在有任何故障問題之后才能夠操作使用設備正常運行，避免在操作中可能存在的各種不良問題。
The operating environment of automatic feeding mixer is usually not very good, which also leads to the need for us to have a detailed understanding of the equipment before operation. After ensuring that the equipment does not have any fault problems, it can be operated and used normally, so as to avoid all kinds of bad problems that may exist in the operation.
我們在運輸自動上料攪拌機的時候要考慮好道路的顛簸問題，因為往往我們運輸過程中發現，很多司機都會采取緊急剎車跟緊急制動等操作，也往往是因為這些操作導致我們的自動上料攪拌一體機發生碰撞跟側滑，所以我們在發貨的時候一定要好好的囑咐我們的司機師傅，要小心去運輸，這樣一來就避免出現很多問題。
When we transport the automatic feeding mixer, we should consider the bumpy problem of the road, because we often find that many drivers will take emergency braking and emergency braking and other operations, which often lead to collision and sideslip of our automatic feeding mixer. Therefore, we must give our company good instructions when delivering the goods Machine master, to be careful to transport, so as to avoid many problems.

 

首頁 產品 電話 置頂