啟動攪拌車自動上料的和液壓系統，以便將在泵上獲得的動量用于為液壓馬達提供動力。準備幾乎自動啟動排水泵，切換到清潔狀態并控制操作按鈕。排空水箱中的水，打開水箱底部的排水球閥，然后等待水箱中的水流出。按下排水系統按鈕，觀察泵出口的狀況。當供水停止從泵出口流出時，操作完成，泵中的水完全排出。
Start the automatic feeding and hydraulic system of the mixer so that the momentum obtained on the pump can be used to provide power for the hydraulic motor. Prepare to start the drainage pump almost automatically, switch to clean state and control the operation button. Drain the water in the water tank, open the drain ball valve at the bottom of the water tank, and then wait for the water in the water tank to flow out. Press the drain system button to observe the condition of the pump outlet. When the water supply stops flowing out from the pump outlet, the operation is completed and the water in the pump is completely discharged.
根據以上過程，攪拌車自動上料的泵干凈地排出，冬天不怕泵開裂。請注意，每次使用泵時，都必須將其排干。否則，它將在一夜之間被完全破壞，將無法使用。另外，在攪拌車自動上料的強制排水過程中，必須注意泵的出口。
According to the above process, the automatic feeding pump of the mixer is discharged cleanly, and the pump is not afraid of cracking in winter. Please note that the pump must be drained every time it is used. Otherwise, it will be completely destroyed overnight and will be unusable. In addition, attention must be paid to the outlet of the pump in the forced drainage process of automatic feeding of the mixer.
攪拌車自動上料的保養
Maintenance of automatic feeding of mixer truck
對于攪拌車自動上料的設備，發動機的使用非常重要，因此在正常設備制造過程中必須維護發動機。這是一些正確的發動機維護方法。
For the automatic feeding equipment of mixer, the use of engine is very important, so the engine must be maintained in the normal equipment manufacturing process. These are some of the right ways to maintain the engine.
1.，攪拌車自動上料的設備用塑料膜覆蓋，然后在膜的上側用半濕毛巾覆蓋，以防止高壓水涌入分配器，從而使攪拌車自動上料的難以啟動。
1. First, the automatic feeding equipment of the mixer is covered with plastic film, and then the upper side of the film is covered with semi wet towel to prevent high-pressure water from flowing into the distributor, which makes it difficult to start the automatic feeding of the mixer.
2.用高壓水槍從攪拌車自動上料的頂部到底部附著在發動機側和發動機側的污垢。
2. Use a high-pressure water gun to remove the dirt attached to the engine side and engine side from the top to the bottom of the mixer.
3.浸濕后，將攪拌車自動上料的外部清潔劑直接噴到攪拌機的發動機和機艙中。
3. After soaking, spray the external cleaning agent automatically fed by the mixer directly into the engine and engine room of the mixer.
4.閃爍3分鐘后，使用纖維刷清潔機房中所有可接觸的部件。
4. After flashing for 3 minutes, use the fiber brush to clean all accessible parts in the machine room.
5.用高壓水槍快速沖洗被擦洗的污垢。
5. Use a high-pressure water gun to quickly wash the scrubbed dirt.
6.然后在發動機表面噴涂攪拌車自動上料的發動機外部清潔劑，操作步驟與上述相同。重復進行直攪拌車自動上料的表面被清潔。
6. Then spray the engine external cleaning agent automatically fed by mixer truck on the engine surface, and the operation steps are the same as above. Repeat until the automatic feeding surface of the mixer is cleaned.
This article is organized and released by the automatic feeding mixer. Do you know something about these contents? For more information, please click: http://www.ksmayo.cn We'll have a lot more to see.
山汽微信
2022-12-23
首頁
產品
電話
置頂