有些用戶會見到有些操作混凝土攪拌機的工作人員會在混凝土攪拌機傳動齒輪每天開機前應涂抹黃油少許.并在鏈條上加涂少量的潤滑脂,每工作300小時清洗鏈條一次,每星期打開一次各傳動鏈條罩殼。混凝土攪拌機每班工作結束后將混合料存?zhèn)}中的物料排放干凈,切斷總電源,檢查攪拌臂與葉漿的緊固情況,發現螺母松動應立即擰緊,這些都是日常所需要注意的。混凝土攪拌機的使用壽命與日常保養有相當大的關系,
全自動上料攪拌機維修和保養應注意以下幾點:
Some users will see that some workers who operate the concrete mixer will apply a little butter before starting the concrete mixer drive gear every day, and apply a small amount of grease on the chain, clean the chain once every 300 hours, and open the cover of each drive chain once a week. After the end of each shift of the concrete mixer, the materials in the storage bin of the mixture shall be discharged, the main power supply shall be cut off, and the fastening condition between the mixing arm and the blade slurry shall be checked. If the nut is loose, it shall be tightened immediately. These are the daily needs. The service life of concrete mixer is closely related to daily maintenance. The following points should be paid attention to in the maintenance and repair of full-automatic feeding mixer:
(1)各部分緊固螺栓經常檢查,特別是攪拌機座、電機座、葉片與襯板,以防松脫。
(1) Check the fastening bolts of all parts, especially the mixer base, motor base, blade and lining plate, to prevent loosening.
(2)更換混凝土攪拌機葉片時應用標準扭力扳手,鎖緊力矩應達200-220N.m。
(2) When replacing the blade of concrete mixer, the standard torque wrench should be used, and the locking torque should be 200-220n. M.
(3)混凝土攪拌機攪拌葉片與襯板之間磨損間隙過大時,筒體水平兩側應調≤5mm。
(3) When the wear clearance between the mixing blade and the lining plate of the concrete mixer is too large, the horizontal sides of the cylinder should be adjusted to ≤ 5mm.
(4)減速機潤滑油要按標準定期更換。
(4) The lubricating oil of reducer shall be changed regularly according to the standard.
(5)檢查混凝土攪拌機潤滑泵是否按程序設置正常工作。
(5) Check whether the lubrication pump of concrete mixer works normally according to the program setting.
(6)每班次或停機前要清洗攪拌桶、軸、葉片。
(6) Clean the mixing drum, shaft and blade before each shift or shutdown.
(7)同步齒輪、傳動鏈條要定期清理,加潤滑油脂。
(7) The synchronous gear and transmission chain should be cleaned regularly and lubricated.
(8)冰凍季節,應將噴水系統內存水放凈。
(8) In the freezing season, the water in the sprinkler system should be drained.
The above is a detailed introduction to the maintenance precautions of automatic feeding mixer. If you want to know more, please consult http://www.ksmayo.cn Official website.