久久综合给合久久狠狠狠97色69,国产欧美在线观看不卡,少妇高潮流白浆在线观看,亚洲熟女精品中文字幕

山東山汽工程機械（集團）有限公司
熱線電話：400-879-1999 山汽微信
鄭重聲明 購機 售后
在線詢價
熱線電話：400-879-1999
您現在所在的位置: 首頁> 新聞資訊 > 行業新聞

混凝土攪拌車底盤潤滑的注意事項！

所屬分類：行業新聞 發布時間：2020-09-10 來源：http://www.ksmayo.cn 瀏覽量：0

　　混凝土攪拌車底盤潤滑的注意事項！
　　Concrete mixer chassis lubrication precautions!
　　對水泥攪拌車底盤進行正確的潤滑可以減少汽車零件的磨損，增加攪拌車零件的使用壽命，但是在實施潤滑時應注意一下幾點：
　　Proper lubrication of cement mixer chassis can reduce the wear of automobile parts and increase the service life of mixer parts. However, the following points should be paid attention to when carrying out lubrication:
　　1、正常使用情況下，按攪拌車廠家的保養周期進行潤滑，環境惡劣情況下要適當縮短保養周期。
　　1. Under normal use, lubrication shall be carried out according to the maintenance cycle of the mixer manufacturer, and the maintenance period shall be shortened appropriately under harsh environment.
　　2、要選用規定的潤滑油。代用油料須性能接近，主要技術指標須保證，并且用代用油應時常檢查，且縮短使用周期。
　　2. Select the specified lubricating oil. The performance of substitute oil must be close to each other, the main technical indexes must be guaranteed, and the substitute oil should be inspected frequently and the service life should be shortened.
　　3、更換發動機機油時，要在熱狀態時進行，以保證油能放盡。放油時應注意檢查機油顏色是否正常、機油有無異物，以便發現故障隱患。待油放盡后，放油螺栓上的異物，然后擰緊。
　　3. When changing the engine oil, it should be carried out in the hot state to ensure that the oil can be drained completely. Pay attention to check whether the oil color is normal and whether there are foreign matters in the oil when discharging, so as to find out the hidden trouble. After the oil is drained out, drain the foreign matters on the oil bolt, and then tighten it.
             全自動上料攪拌車
　　4、進行潤滑前，要清潔入口。潤滑后要清潔零件表面，以免沾上塵土和污物。
　　4. Clean the inlet before lubrication. Clean the surface of parts after lubrication to avoid dust and dirt.
　　5、更換新機油濾芯，將新機油注入發動機到油尺上限。為防止在沒有潤滑油的情況下啟動發動機，應使高壓油泵處于斷油位置時按啟動按鈕，空轉一會兒后，再啟動發動機，并低速運轉。檢查機油濾清器有無滲漏，停機后，檢查并補充機油油面到油尺上。
　　5. Replace the oil filter element and fill the engine with new oil to the upper limit of the oil dipstick. In order to prevent the engine from starting without lubricating oil, press the start button when the high-pressure oil pump is at the oil cut-off position. After idling for a while, start the engine and run at low speed. Check the oil filter for leakage. After shutdown, check and replenish the oil level to the dipstick.
　　6、換機油濾芯：更換機油時，機油濾清器要同時更換，在密封墊上涂上一層薄薄的油，并且緊固濾清器。
　　6. Change the oil filter element: when changing the engine oil, the oil filter should be replaced at the same time. Apply a thin layer of oil on the sealing gasket and fasten the filter.

 

首頁 產品 電話 置頂