正確操作全自動小型上料攪拌車的注意事項，生產的全自動小型上料攪拌車的液壓系統壓力應符合使用說明書中的規定，不得隨意調整。液壓油的油質和油量應符合原定要求。全自動小型上料攪拌車裝料前，應先排凈拌筒內殘存的積水和雜物。在運輸過程中要不停的轉動，以防混凝土離析。全自動小型上料攪拌車到達工地和卸料之前，應先使拌筒全速以14-18轉/分轉動1-2分鐘，然后再進行反轉卸料。反轉之前，應使攪拌筒停穩不轉。
The hydraulic system pressure of the full-automatic small loading mixer should be in accordance with the provisions in the operation manual, and should not be adjusted at will. The quality and quantity of hydraulic oil should meet the original requirements. Before loading, the residual water and debris in the mixing drum should be drained. In the process of transportation, keep rotating to prevent concrete segregation. Before the full-automatic small loading mixer arrives at the construction site and unloads, the mixing drum should be rotated at full speed at 14-18 rpm for 1-2 minutes, and then reverse the unloading. Before reversing, the mixing drum should be stopped stably.
全自動小型上料攪拌車罐內溫度高于25攝氏度，從裝料，運輸，到卸料延續時間不得超過60分鐘，環境溫度低于25攝氏度，上述時間不得超過90分鐘。冬期施工時應切實做到：開機前檢查是否結冰;下班時認真排除拌筒內及供水系統內殘存積水，關閉水泵開關，將控制手柄置于“停止”位置。
When the temperature in the tank of the full-automatic small loading mixer is higher than 25 ℃, the duration from loading, transportation to unloading shall not exceed 60 minutes, and the above time shall not exceed 90 minutes when the ambient temperature is lower than 25 ℃. During winter construction, it is necessary to check whether there is icing before starting the machine; when off duty, carefully remove the residual water in the mixing drum and water supply system, turn off the water pump switch, and put the control handle at the "stop" position.
攪拌車在施工現場卸料完畢后，應立即用攪拌車隨帶的軟管沖洗進料斗，出料斗，卸料溜槽等處，粘附在車身各處的污泥及混凝土。在返回攪拌站的途中，應向攪拌筒內注150 --- 200L水以清洗筒壁及葉片粘結的混凝土殘渣。
After the mixer truck is unloaded at the construction site, the inlet hopper, discharge hopper, discharge chute and other places shall be washed with the hose attached to the mixer to remove the sludge and concrete adhered to the vehicle body. On the way back to the mixing station, 150-200l water should be injected into the mixing drum to clean the concrete residue bonded by the cylinder wall and blades.
全自動小型上料攪拌車在工作時，不得將手伸入旋轉的攪拌筒內，嚴禁將手伸入主卸料溜槽和加長卸料溜槽的連接部位，以免發生事故。應定期檢查攪拌葉片磨損情況并及時進行修補和換新。各項有關操作規范。混凝土攪拌運輸車司機須經過培訓，無合格證者不得上崗操作。
When the full-automatic small loading mixer is working, it is not allowed to put hands into the rotating mixing drum, and it is strictly prohibited to put hands into the connection part of the main discharge chute and the extended discharge chute, so as to avoid accidents. The abrasion of mixing blades should be checked regularly and repaired and replaced in time. All relevant safety operation specifications. The driver of concrete mixer truck must be trained professionally, and the operator without certificate is not allowed to work.
全自動小型上料攪拌車常見維護問題，全自動小型上料攪拌車廠家告訴您使用小型攪拌罐車的時候出現罐體問題的，是如何造成如何呢，今在“錢”進的路上沒有障礙，我們時刻為你為您著想，全自動小型上料攪拌車出現罐體質量問題，只能眼睜睜的看著混凝土凝固，鄭州漫星專在這個點提出方案，有了它再也不用擔心混凝土凝固的問題了。
Full automatic small loading mixer common maintenance problems, automatic small mixing truck manufacturers tell you the use of small mixing tank truck tank problems, how to solve? Today, Zhengzhou manxing in order to everyone in the "money" on the road, we always think for you, full-automatic small feeding mixer tank body quality problems, only To be able to watch the concrete solidification, Zhengzhou manxing puts forward a solution at this point. With it, there is no need to worry about the problem of concrete solidification.
導致全自動小型上料攪拌車的主要原因：
The main reasons for the automatic small loading mixer are as follows:
1.全自動小型上料攪拌車發動機故障：發動機無法啟動，取力器損壞等原因。
1. Engine failure of full-automatic small loading mixer: the engine cannot be started and the power take-off is damaged.
2.上裝罐的故障：傳動軸損壞，油泵故障，液壓油過臟或油量不足，馬達故障，減速機故障，操縱桿松脫等原因。
2. Faults of top loading tank: damaged transmission shaft, oil pump failure, dirty or insufficient hydraulic oil, motor failure, reducer failure, loose control rod, etc.
山汽微信
2022-12-23
首頁
產品
電話
置頂