由于篩網采用普通鋼材，經常存在質量差、耐磨性差的問題，包角不夠合理，因此在應用過程中容易損壞，出現大面積滲漏，甚混音器也無法使用。
Because the screen is made of ordinary steel, there are often problems of poor quality and poor wear resistance, and the wrap angle is not reasonable enough. Therefore, it is easy to be damaged in the application process, large-area leakage occurs, and even the mixer can not be used.
另外，有些攪拌篩的目數不夠科學，篩分率太低，導致已篩分的砂石粒度小。如果自上料攪拌車的篩網尺寸不夠合理，鋼材質量不達標，那么再的自上料攪拌車也無法攪拌出高質量的混凝土。
In addition, the mesh number of some mixing screens is not scientific enough, and the screening rate is too low, resulting in small particle size of screened sand and stone. If the screen size of the self loading mixer is not reasonable enough and the steel quality does not meet the standard, the most advanced self loading mixer can not mix high-quality concrete.
自上料攪拌車篩網故障維修中應使用耐磨鋼絲，設置科學的鋼絲直徑和篩網目數，適當增加篩網的面積，提高篩分率，節約原料，從而提高生產效率。發現篩線斷線后，立即擰緊篩網螺栓，重新設置篩網長度。
Wear resistant steel wire should be used in the maintenance of screen fault of self loading mixer truck, set scientific steel wire diameter and screen mesh, appropriately increase the screen area, improve the screening rate and save raw materials, so as to improve the production efficiency. When the screen wire is broken, immediately tighten the screen bolt and reset the screen length.
自上料攪拌車篩網葉片出現故障需及時維修
If the screen blade of the self loading mixer fails, it shall be repaired in time
此外，葉片故障也是一個重大故障。葉片作為自上料攪拌車設備的重要部件之一，對攪拌過程有著直接的影響，葉片的好壞在一定程度上可以決定自上料攪拌車的使用壽命。因此，在自上料攪拌車使用過程中，葉片的損壞程度往往比較高，因此需要注意葉片技術。
In addition, blade failure is also a major failure. As one of the important components of the self loading mixer, the blade has a direct impact on the mixing process. The quality of the blade can determine the service life of the self loading mixer to a certain extent. Therefore, in the process of using the self loading mixer, the damage degree of the blade is often high, so we need to pay attention to the blade technology.
自上料攪拌車每次攪拌完畢后，需要立即清洗自上料攪拌車的葉片，以便及時清理葉片上的污垢。自上料攪拌車的葉片和振動軸承應滴上潤滑油，自上料攪拌車的葉片應防銹除銹。
After each mixing of the self loading mixer truck, the blades of the self loading mixer truck need to be cleaned immediately in order to clean the dirt on the blades in time. The blades and vibration bearings of the self loading mixer shall be dripping with lubricating oil, and the blades of the self loading mixer shall be rust proof and derusted.
自上料攪拌車廠家認為，定期檢查自上料攪拌車的葉片手柄和葉片焊接質量，檢查葉片磨損和消耗情況。一旦發現異常問題，應及時記錄并更換，并檢查刀片底部導通狀態，避免刀片損壞。泄漏發生在焊點處。
The manufacturer of self loading mixer truck believes that the welding quality of blade handle and blade of self loading mixer truck shall be inspected regularly, and the blade wear and consumption shall be inspected. Once any abnormal problem is found, it shall be recorded and replaced in time, and the conduction state at the bottom of the blade shall be checked to avoid blade damage. Leakage occurs at the solder joint.
The wonderful content of this article is provided by the knowledge of automatic feeding mixer. There are many wonderful contents on this website. You can click to enter more contents: http://www.ksmayo.cn/ We have special customer service to answer your questions
山汽微信
2022-12-23
首頁
產品
電話
置頂