久久综合给合久久狠狠狠97色69,国产欧美在线观看不卡,少妇高潮流白浆在线观看,亚洲熟女精品中文字幕

山東山汽工程機械（集團）有限公司
熱線電話：400-879-1999 山汽微信
鄭重聲明 購機 售后
在線詢價
熱線電話：400-879-1999
您現在所在的位置: 首頁> 新聞資訊 > 行業新聞

自動上料攪拌車停油要具備的維修知識

所屬分類：行業新聞 發布時間：2022-09-17 來源：http://www.ksmayo.cn 瀏覽量：0

自動上料攪拌車工作量大，用戶只要具備一定的維修知識，對使用會有很大幫助。不過，機械漏油是很常見的問題，今天就教大家這些小技巧。
The workload of the automatic feeding mixer truck is large. As long as the user has certain maintenance knowledge, it will be very helpful to use it. However, mechanical oil leakage is a common problem. Today, I will teach you these tips.
過度使用和油封是正常磨損情況。方法：更換新油封即可。
Excessive use and oil seals are normal wear conditions. Solution: Replace the oil seal with a new one.
長時間不更換機油，濾芯質量不合格，機油太臟，加速油封磨損。方法：盡快更換液壓油和濾芯。
If the engine oil is not replaced for a long time, the filter element is unqualified, the engine oil is too dirty, and the oil seal is accelerated to wear. Solution: Replace the hydraulic oil and filter element as soon as possible.
傳動軸平衡失效，擺動大，造成主軸擺動油封偏磨。方法：及時糾正并更換轉軸。液壓油變質乳化，導致潤滑性能下降，加速油封磨損。方法：盡快更換液壓油和濾芯，嚴重時需要清洗系統。泵支架松動，開泵，泵固定螺栓松動，進而引起液壓泵整體振動和油封磨損。
The balance of the transmission shaft fails and the swing is large, causing eccentric wear of the main shaft swing oil seal. Solution: Correct and replace the shaft in time. The hydraulic oil is deteriorated and emulsified, which leads to the decline of lubricating performance and accelerates the wear of oil seals. Solution: replace the hydraulic oil and filter element as soon as possible, and clean the system in serious cases. The pump bracket is loose, the pump is started, and the pump fixing bolts are loose, which causes the overall vibration of the hydraulic pump and the wear of the oil seal.
方法：經常檢查和排除自動上料攪拌車可能出現的故障，防止和避免故障。
Solution: Frequently check and eliminate possible faults of automatic feeding mixer truck to prevent and avoid faults.
自動上料攪拌系統回油不暢，回油管和散熱器堵塞，進而導致電機殼內壓力升高，造成油封漏油。方法：堵塞物，保持回油循環通暢。如果散熱器不散熱，油溫過高，粘度和潤滑性下降，油封過熱，密封失效。方法：對散熱器進行故障排除，對系統進行冷卻過程，避免泵電機磨損。嚴重時，停止發動機并熄火，用水沖洗泵電機和散熱器外殼，以達到冷卻效果。
The oil return of the automatic feeding and mixing system is not smooth, and the oil return pipe and radiator are blocked, which leads to the pressure rise in the motor housing and oil leakage of the oil seal. Solution: Remove the blockage and keep the oil return circulation smooth. If the radiator does not dissipate heat, the oil temperature is too high, the viscosity and lubricity are reduced, the oil seal is overheated, and the seal fails. Solution: Troubleshoot the radiator and cool the system to avoid wear of the pump motor. In serious cases, stop the engine and shut down, flush the pump motor and radiator housing with water to achieve cooling effect.
自動上料攪拌車
Automatic feeding mixer
以上就是為大家介紹的有關全自動上料攪拌車的詳細的介紹,希望對您有所幫助.如果您有什么疑問的話,歡迎聯系我們.我們將以的態度,為您提供服務http://www.ksmayo.cn
The above is a detailed introduction to the fully automatic feeding mixer, and I hope it will be helpful to you. If you have any questions, please contact us. We will provide services for you with our attitude http://www.ksmayo.cn

 

首頁 產品 電話 置頂