全自動上料攪拌車具有許多優點，可大大提高生產效率。自動攪拌，省時省力;罐體可提升、旋轉、升級;鉸接式，方便靈活;4輪驅動，通度好;它只需要燃料消耗，不需要外部供電，對于偏遠山區和無電地區的施工特別方便。成本低，維護方便。然而，隨著油價的上漲，如何節約燃料消耗已經成為人們關注的問題，而作為建筑工程車輛，燃料消耗更為重要，如何降低油耗呢?
The full-automatic feeding mixer has many advantages, which can greatly improve the production efficiency. Automatic mixing saves time and labor; the tank body can be lifted, rotated and upgraded; articulated, convenient and flexible; 4-wheel drive, good connectivity; it only needs fuel consumption, does not need external power supply, and is particularly convenient for construction in remote mountainous areas and areas without electricity. Low cost and convenient maintenance. However, with the rise of oil price, how to save fuel consumption has become a concern. As a construction vehicle, fuel consumption is more important. How to reduce fuel consumption?
一、八招教你將全自動上料攪拌車的油耗降到更低
1、 Eight Tips to reduce the fuel consumption of the full-automatic feeding mixer
1.在駕駛中發現，現在攪拌器滑行距離明顯縮短，這時司機應檢查攪拌器輪胎壓力是否達到壓力標準。如果輪胎充氣不足，燃料消耗會增加。提示:適當給輪胎充氣。
1. During driving, it is found that the taxi distance of agitator is obviously shortened. At this time, the driver shall check whether the tyre pressure of agitator meets the pressure standard. If the tires are under inflated, fuel consumption will increase. Tip: properly inflate the tire.
2.檢查全自動上料攪拌車的輪胎磨損情況，如果輪胎磨損嚴重，經常會出現打滑現象，增加油耗。提示:必要時更換新輪胎。
2. Check the tire wear of the full-automatic loading mixer. If the tire is seriously worn, it will often slip and increase fuel consumption. Tip: replace the tire if necessary.
3.當全自動上料攪拌車運行或啟動時，如果車輪有異常噪音，應及時檢查軸承和剎車系統。如果輪的轉動不正常，就會影響全自動上料攪拌車的速度，從而影響燃油的消耗。提示:大修軸承和剎車系統。
3. When the full-automatic loading mixer is running or starting, if there is abnormal noise on the wheel, check the bearing and brake system in time. If the rotation of the wheel is not normal, it will affect the speed of the full-automatic feeding mixer, thus affecting the fuel consumption. Tip: overhaul the bearing and brake system.
4.攪拌器離合器打滑會造成發動機轉數損失。當你發現在快速加速的攪拌器中發動機轉速表增加得非常快，而速度增加得非常慢時，你就可以斷定離合器打滑了。提示:需要更換離合器片、離合器片和驅動輪。
4. The clutch of agitator slips, which will cause the loss of engine speed. When you find that the engine tachometer increases very fast and the speed increases very slowly in the fast accelerating mixer, you can conclude that the clutch is slipping. Tip: the clutch plate, clutch plate and drive wheel need to be replaced.
5.當全自動上料攪拌車行駛了二三十萬后，通常會出現缸內壓力不足的現象，這時油耗會顯著增加。提示:如果發生這種情況，攪拌器發動機將需要大修。
5. When the full-automatic loading mixer has been running for 230000km, the pressure in the cylinder is usually insufficient, and the fuel consumption will increase significantly. Tip: if this happens, the agitator engine will need to be overhauled.
6.當排氣管冒出黑煙，燃油消耗增加時，檢查化油器。提示:如果化油器太臟，將清潔劑直接噴到化油器的入口。如有黑煙，應將化油器拆開清洗。
6. When the exhaust pipe emits black smoke and fuel consumption increases, check the carburetor. Tip: if the carburetor is too dirty, spray detergent directly to the inlet of the carburetor. In case of black smoke, the carburetor shall be disassembled for cleaning.
7.如果攪拌車火花塞使用時間過長，還會出現油耗增加的現象。由于全自動上料攪拌車的火花塞損壞會降低點火能量，使汽車加速緩慢，導致油耗顯著增加。提示:應更換攪拌機的火花塞。
7. If the spark plug is used for a long time, the fuel consumption will increase. Due to the damage of the spark plug of the full-automatic charging mixer, the ignition energy will be reduced, the vehicle will accelerate slowly, resulting in a significant increase in fuel consumption. Tip: the spark plug of mixer should be replaced.
8.當全自動上料攪拌車溫度開關和恒溫器損壞時，會有油耗的增加。由于全自動上料攪拌車的溫控開關和恒溫器的損壞會降低水的溫度，化油器不能正常工作，導致全自動上料攪拌車的油霧化差，油耗顯著增加。
8. When the temperature switch and thermostat of the full-automatic feeding mixer are damaged, the fuel consumption will increase. Due to the damage of the temperature control switch and thermostat of the full-automatic feeding mixer, the water temperature will be reduced, and the carburetor will not work normally, resulting in the poor oil atomization of the full-automatic feeding mixer, and the fuel consumption will be significantly increased.
如何減少全自動上料攪拌車的燃料消耗
How to reduce the fuel consumption of full-automatic loading mixer
二、全自動上料攪拌車在使用時注意五個事項
2、 Five points for attention when using the full-automatic feeding mixer
1. 全自動上料攪拌車應停在地上，將勺子放在地上。在發動機熄火時，需反復轉動工作裝置的操作手柄，確保各液壓缸處于無壓靜止狀態。當攪拌器僅停在斜坡上時，固定好輪胎。
1. The full-automatic feeding mixer shall be parked on the ground and the spoon shall be placed on the ground. When the engine is off, it is necessary to turn the operating handle of the working device repeatedly to ensure that each hydraulic cylinder is in a static state without pressure. When the mixer stops only on the slope, fix the tire.
2. 自動上料攪拌機停止工作后，操作者將各種手柄放在空擋或中間位置。
2. After the automatic feeding mixer stops working, the operator will put various handles in neutral or middle position.
3.取下電源鎖鑰匙，然后關閉電源主開關，關閉門窗。
3. First remove the power lock key, then turn off the main power switch, and finally close the doors and windows.
4、嚴禁將全自動上料攪拌車停在明火或高溫區域，以防熱爆輪胎，造成事故。
4. It is strictly prohibited to park the full-automatic loading mixer in the open fire or high temperature area to prevent the tire from thermal explosion, resulting in accidents.
5. 使用組合閥或儲氣罐給輪胎充氣時，不得站在自動加料攪拌車的輪胎前方，以免爆炸傷到人。
5. When using combination valve or air tank to inflate the tire, do not stand in front of the tire of automatic feeding mixer to avoid personal injury caused by explosion.
山汽微信
2022-12-23
首頁
產品
電話
置頂