全自動上料攪拌機是特殊的重型車,當混合燃料箱時,負載能力大并且道路條件變得復雜。由于慣性離心力的增加,對全自動上料攪拌機系統的制動系統提出了很高的要求。制動系統對于混合器系統非常重要,但是確定混合器時首先要考慮的是轎廂的制動距離和制動器的熱降解。如果卡車的制動系統出現問題,駕駛員和乘客也有危險。因此,踩踏或踩踏制動器時,請務必小心。
Full automatic loading mixer is a special heavy-duty vehicle. When mixing fuel tanks, the load capacity is large and the road conditions become complex. Due to the increase of inertial centrifugal force, high requirements are put forward for the braking system of full-automatic feeding mixer system. The braking system is very important for the mixer system, but when determining the mixer, the first consideration is the braking distance of the lift car and the thermal degradation of the brake. If there is a problem with the braking system of the truck, the driver and passengers are also at risk. Therefore, be careful when applying or applying the brake.
1.制動時發出異常聲音;踩剎車時,剎車系統會引起強烈的金屬摩擦。原因可能是剎車片上的異物或剎車盤生銹。
1. Abnormal sound during braking; When stepping on the brake, the brake system will cause strong metal friction. The reason may be foreign matters on the brake pad or rust on the brake disc.
2.制動踏板的行程變長;剎車變軟時,您會看到筆直的白點。較長的制動沖程主要是由于空氣進入制動系統,缺少制動油,可能的泄漏和制動襯塊的嚴重磨損。
2. The stroke of the brake pedal becomes longer; When the brakes soften, you will see straight white spots. The longer braking stroke is mainly due to air entering the braking system, lack of brake oil, possible leakage and serious wear of brake pads.
3.制動偏差;制動器打滑不太常見,主要反映了在施加制動器時方向盤向一側彎曲的事實。造成這種現象的原因可能是制動襯塊偏心磨損和制動分泵出現問題。
3. Braking deviation; Brake slip is less common and mainly reflects the fact that the steering wheel bends to one side when the brake is applied. This phenomenon may be caused by eccentric wear of brake pads and problems of brake wheel cylinder.
4.剎車越來越難;許多卡都有增加制動的問題。加強制動器的主要原因是真空助力器故障。剎車不輔助,經常使用剎車。
4. Braking becomes more and more difficult; Many cards have the problem of increasing braking. The main reason for strengthening the brake is the failure of the vacuum booster. The brake is not assisted, and the brake is often used.
5.剎車回彈;許多卡伙伴都遇到過這種情況,但是在制動時,會出現一種現象,其中上肢從制動踏板上彈起,主要是由于制動盤表面不平整。墊片和鋼環變形。
5. Brake rebound; Many card partners have encountered this situation, but when braking, there will be a phenomenon in which the upper limb bounces from the brake pedal, mainly due to the uneven surface of the brake disc. The gasket and steel ring are deformed.
The above is a detailed introduction to the automatic feeding mixer. I hope it will be helpful to you If you have any questions, please contact us We will provide you with professional service http://www.ksmayo.cn/