自上料攪拌車，操作簡單出料迅速，優勢更明顯！
Since the loading mixer, the operation is simple and the discharging is fast, the advantage is more obvious!
自上料水泥攪拌車廣泛適用于住宅建筑、鄉村修路、修建廣場、車間……等路面比較窄的硬化施工作業的專用車輛。該產品具有自上料、自供水、自攪拌，270度左旋右轉全地形大角度下料，高壓自動沖洗罐體，多功能為一體的工程攪拌車。
Self loading cement mixer is widely used in residential buildings, rural road construction, building squares, workshops... And other special vehicles for hardening construction with narrow roads. This product has a multi-function engineering mixer with self loading, self water supply, self mixing, 270 ° left rotation and right rotation, all terrain large angle unloading, high-pressure automatic tank washing.
自上料攪拌車優勢
Advantages of self loading mixer
一、操作靈活方便，時間繼電器加水使攪拌更均勻，更符合標準。操作桿操作方便。
1、 The operation is flexible and convenient. The time relay adds water to make the mixing more uniform and more in line with the standard. The operating lever is easy to operate.
二、前置雙輪真空鋼絲輪胎承重更大，減少意外的發生。
2、 The front double wheel vacuum steel wire tire has greater load-bearing and reduces accidents.
三、高壓洗車槍，清洗車輛更干凈！方便快捷，出料的時候能夠非常的方便清洗。不需要人工手動清洗。
3、 High pressure car washing gun makes the car cleaner! It is convenient and fast, and it is very convenient to clean when discharging. Manual cleaning is not required.
四、每天工作要少省10個人工，節約100度電，不用混泥土運輸車和裝載機上料，全地形工作。
4、 Work every day to save 10 labor, save 100 degrees of electricity, no concrete truck and loader loading, all terrain work.
五、駕駛室操作臺可旋轉，前后雙向駕駛更方便。車輛可傾斜式卸料功能，使卸料更干凈，速度更快，傾斜式卸料設計讓車輛卸料更加貼合實際。
5、 The cab console can be rotated, which makes it more convenient to drive in both directions. The tilting unloading function of the vehicle makes the unloading cleaner and faster. The tilting unloading design makes the unloading of the vehicle more practical.
自動上料攪拌車使用前應做到
The automatic feeding mixer shall meet the following requirements before use
1、檢查各個水箱是否缺水并加足水，輪胎氣壓是否符合2.5bar以_上要求。
1. Check whether each water tank is short of water and add enough water, and whether the tire pressure meets 2.5bar_ Requirements.
2、檢查發動機機油油尺，液壓油箱標尺，齒輪箱油標觀察孔，前、后橋，輪邊減速軸頭擰開油面油堵檢查齒輪油是否符合要求，缺少應及時添加，總泵自動液油杯液面是否合乎標準要求。
2. Check the engine oil dipstick, hydraulic oil tank dipstick, gearbox oil gauge observation hole, front and rear axles, wheel reduction shaft head, unscrew the oil level oil plug, and check whether the gear oil meets the requirements. If it is missing, it should be added in time, and whether the liquid level of the master cylinder automatic oil cup meets the standard requirements.
3、觀測發動機機油，齒輪油，檢查油標尺，油標鑼孔，液壓油箱時，車輛要水平位置。
3. Observe the engine oil and gear oil, and check the oil dipstick, the Gong hole of the oil pointer, and the hydraulic oil tank. The vehicle should be in a horizontal position.
4、全車各部油管路，氣管路接頭是松動有無漏油，漏氣現象。檢查全車線路有無接觸不良，各儀表，燈光是否工作正常。
4. The oil pipeline and gas pipeline joints of all parts of the vehicle are loose, and whether there is oil leakage or air leakage. Check whether the circuit of the whole vehicle has poor contact and whether the instruments and lights work normally.
5、行駛前剎車是否制動有效，檢查各操縱閥作用是否良好。
5. Check whether the brake is effective before driving and whether the control valves work well.
The above is the content introduced for the automatic feeding mixer truck. Thank you for checking the information of our company in your busy schedule. If you want to know more, you are welcome to call for consultation! http://www.ksmayo.cn/
山汽官方微信
2022-12-23
首頁
產品
電話
置頂