久久综合给合久久狠狠狠97色69,国产欧美在线观看不卡,少妇高潮流白浆在线观看,亚洲熟女精品中文字幕

山東山汽工程機械（集團）有限公司
熱線電話：400-879-1999 山汽微信
鄭重聲明 購機 售后
在線詢價
熱線電話：400-879-1999
您現在所在的位置: 首頁> 新聞資訊 > 行業新聞

自動上料攪拌機施工的各部位操作

所屬分類：行業新聞 發布時間：2021-02-26 來源：http://www.ksmayo.cn 瀏覽量：0

1.攪拌車攪拌筒的旋轉由液壓馬達通過專用行星減速機帶動，行星減速機的輸出軸可以實現一定角度的擺動，以滿足惡劣路況下攪拌筒的跳動。
1. The rotation of the mixer drum is driven by the hydraulic motor through a special planetary reducer. The output shaft of the planetary reducer can realize a certain angle swing to meet the beating of the mixer drum under bad road conditions.
2.液壓系統采用恒功率變量柱塞泵，減少發動機的功率損耗。
2. Constant power variable piston pump is used in the hydraulic system to reduce the power loss of the engine.
3.進水系統可根據計量設定實現自動進水。
3. The water inlet system can automatically feed water according to the metering setting.
4.干料上料，按照設計好的配比由鏟臂、動臂缸、定量的料斗自動上料。
4. Dry material feeding: according to the designed proportion, it is automatically fed by shovel arm, boom cylinder and quantitative hopper.
自動上料攪拌機
5.自動上料攪拌車攪拌筒內壁上設置雙螺旋形葉片，正向旋轉為進料、混凝土攪拌；反向旋轉，在螺旋葉片的推動下、混凝土由出料口出料。
5. Double spiral blades are set on the inner wall of the mixing drum of the automatic feeding mixer, which rotate in the positive direction for feeding and concrete mixing; in the reverse direction, the concrete is discharged from the discharge port under the push of the spiral blades.
6.行走系統由發動機通過液力變矩器、前后傳動軸到前后橋。本發明采用前后雙橋驅動形式。采用液力變矩器減少對發動機的沖擊、延長了發動機的壽命。
6. The traveling system is composed of engine, front and rear transmission shafts and front and rear axles. The invention adopts a front and rear double axle driving form. The hydraulic torque converter is used to reduce the impact on the engine and prolong the service life of the engine.
換油：攪拌機一般每半年需要更換一次潤滑油，潤滑油的型號為32#機械油，換油時，小心擰開油塞，放進其內存油，注意油槍內可能會有剩余的內壓，以防油的噴射。
Oil change: generally, the blender needs to change the lubricating oil every six months. The type of lubricating oil is 32 # machine oil. When changing the oil, carefully open the oil plug and put the oil in the blender. Pay attention to the residual internal pressure in the oil gun to prevent the oil from spraying.
軸承潤滑脂：一般大修時更換一次，潤滑脂量為軸承腔間隙1/3-1/2，潤滑脂采用高溫鈣納基潤滑脂。
Bearing grease: it should be replaced once in general overhaul, and the amount of grease should be 1 / 3-1 / 2 of the bearing cavity clearance. High temperature calcium base grease is recommended.
攪拌機的泄露保護處理：假如滲漏開關保護，表示電機側的機械密封損壞，必須要檢查和修理，打開油室腔的堵塞，排盡其內積液。
Leakage protection treatment of mixer: if the leakage switch is protected, it means that the mechanical seal on the motor side is damaged. It must be checked and repaired. Open the blockage in the oil chamber and drain the liquid in it.
熱門產品 / HOT PRODUCT

 

首頁 產品 電話 置頂