自動上料攪拌車屬于特種專項作業車輛，它有特定的工作環境，發動機水溫難免會有過高的的時候。每當出現有這種情況時會對設備造成一定的影響。那么水溫過高需要怎么處理呢？接下來小編就告訴大家。
Automatic feeding mixer is a special operation vehicle. It has a specific working environment, and the engine water temperature will inevitably be too high. Whenever this happens, it will have a certain impact on the equipment. So what should we do if the water temperature is too high? Next, Xiaobian will tell you.
1、自動上料攪拌車在普通公路上發動機出現了過熱，應該盡快地降低車速，把汽車駛到樹蔭下，或駛到相對比較涼快的地方，把汽車停下來，但這時候不要急于熄火。
1. If the engine of the automatic loading mixer truck overheats on ordinary roads, you should reduce the speed as soon as possible, drive the car to the shade of trees or to a relatively cool place, and stop the car, but don't be in a hurry to turn off the engine at this time.
2、打開發動機罩蓋，讓發動機怠速運轉，等待發動機溫度逐漸恢復正常。在發動機水溫恢復正常之后，將發動機熄火。然后再等待一段時間，直到發動機的水溫充分地下降了之后，再檢查發動機的冷卻水量。
2. Open the engine hood, let the engine idle and wait for the engine temperature to gradually return to normal. After the engine water temperature returns to normal, turn off the engine. Then wait for a period of time until the water temperature of the engine drops sufficiently, and then check the cooling water volume of the engine.
3、這時候自動上料攪拌車發動機的冷卻水量可能大都嚴重不足。按著規定量把冷卻水補足之后，再檢查一下冷卻系統，確認沒有其他故障之后，可以起動發動機，繼續行駛。也要檢查一下水箱百葉窗是不是被異物堵塞，風扇葉的工作情況，發動機皮帶是否打滑，發動機水泵工作情況等。
3. At this time, the cooling water of the automatic charging mixer engine may be seriously insufficient. After replenishing the cooling water according to the specified amount, check the cooling system. After confirming that there are no other faults, start the engine and continue driving. Also check whether the shutter of the water tank is blocked by foreign matters, the working condition of the fan blade, whether the engine belt slips, the working condition of the engine water pump, etc.
混凝土攪拌機設備在操作使用過程中，會因為長時間不停的運轉導致其溫度有所提高，但是如果超過設備本身所能夠承受的溫度，就會導致其設備受到一定的損壞。為此，當設備溫度出現過高的時候，就需要我們對其做好相應的保養工作，下面一起了解一下吧。
During the operation and use of concrete mixer equipment, its temperature will increase due to long-term non-stop operation, but if it exceeds the temperature that the equipment itself can withstand, it will cause certain damage to its equipment. Therefore, when the equipment temperature is too high, we need to do the corresponding maintenance work. Let's learn about it together.
1、防止發動機機體過熱：由于環境溫度比較高，因此發動機容易過熱，要加強對發動機冷卻系統的檢查、保養，這包括水箱、節溫器、水泵、風扇等部件的檢查，并且要注意及時加注冷卻水。當水溫超過100℃時，應在陰涼處停車降溫，讓發動機怠速運轉，并掀開發動機罩幫助散熱。
1. Prevent overheating of engine block: due to the high ambient temperature, the engine is easy to overheat. Strengthen the inspection and maintenance of engine cooling system, including the inspection of water tank, thermostat, water pump, fan and other components, and pay attention to filling cooling water in time. When the water temperature exceeds 100 ℃, stop in a cool place to cool down, let the engine idle, and lift the engine hood to help dissipate heat.
2、防止發動機爆燃：夏季氣溫較高，有時會超過35℃，而這樣的季節，對于一些部件有所老化的汽車來說，發生自然爆燃等的概率也高出很多。所以要做好防范準備。
2. Prevention of engine deflagration: the temperature is high in summer, sometimes exceeding 35 ℃. In this season, the probability of natural deflagration is also much higher for cars with aging parts. So be prepared.
3、防止車漆受損：車漆經過強烈的陽光曝曬，會發舊、起皺，而普通的美容打蠟雖然可以起到一定的預防暴曬效果，但由于任何車蠟都含有矽的成分，久經紫外線照射會銹蝕車漆，留下點點黑斑。車蠟本身起不到增強硬度作用，反而會因溫度過高而很快流失，停車時要注意盡量把車停放在陰涼處。
3. Prevent damage to the car paint: the car paint will become old and wrinkled after strong sunlight exposure. Although ordinary beauty waxing can play a certain role in preventing exposure, because any car wax contains silicon, it will rust the car paint after a long time of ultraviolet radiation, leaving a little black spots. The car wax itself can not enhance the hardness, but will quickly lose due to excessive temperature. When parking, pay attention to parking the car in a cool place as far as possible.
4、防止車胎爆裂：氣溫高所以比較容易爆胎，溫度過高時很容易使輪胎變形，抗拉力下降。而作為輪胎本身，氣壓不標準、輪胎老化、性能減弱，或者在行駛過程中輪胎軋到了堅硬的金屬或其他硬物等情況，都會導致汽車突然間爆胎。
4. Prevent tire burst: the temperature is high, so it is easy to burst. When the temperature is too high, it is easy to deform the tire and reduce the tensile force. As for the tire itself, non-standard air pressure, tire aging, performance weakening, or the tire is rolled to hard metal or other hard objects during driving will lead to sudden tire burst.
5、防止發動機潤滑不良：溫度高時，機油粘度下降造成潤滑不良。所以要經常檢查油量油質，并及時添加或更換。要注意及時清洗機油濾清器、散熱器，保證機油通暢、散熱良好，并盡量避免發動機超負荷工作。
5. Prevent poor engine lubrication: when the temperature is high, the oil viscosity decreases, resulting in poor lubrication. Therefore, the oil quantity and quality should be checked frequently, and added or replaced in time. Pay attention to timely clean the oil filter and radiator to ensure smooth oil and good heat dissipation, and try to avoid overload of the engine.
6、防止剎車制動失靈：制動液在高溫環境中更容易蒸發汽化，在制動管路中形成氣阻，制動蹄片也容易燒蝕，造成制動失靈。所以要經常檢查調整制動系統，下長坡途中應注意停車晾剎，保證制動性能良好。如果發現制動轂發燙，應停車降溫，但不可澆潑冷水，以防制動轂破裂。
6. Prevent brake failure: the brake fluid is easier to evaporate and vaporize in the high temperature environment, forming air resistance in the brake pipeline, and the brake shoes are also easy to be ablated, resulting in brake failure. Therefore, check and adjust the braking system frequently. Pay attention to parking and braking on the way down a long slope to ensure good braking performance. If the brake hub is hot, stop the vehicle to cool down, but do not pour cold water to prevent the brake hub from cracking.
相信大家也都知道任何的機械設備操作使用的過程中都是三分使用，七分保養，只有這樣才能夠保證設備在正常運行中的良好性能，以及延長其設備的使用壽命，希望大家能夠依照這些知識對設備進行合理的施工使用。
I believe we all know that the operation and use of any mechanical equipment is divided into three parts for use and seven parts for maintenance. Only in this way can we ensure the good performance of the equipment in normal operation and prolong the service life of the equipment. I hope you can carry out reasonable construction and use of the equipment according to these knowledge.
山汽微信
2022-12-23
首頁
產品
電話
置頂