新機器的走合保養是非常關鍵的，能延長機器的使用壽命，減少小故障的發生，今天小編帶大家來看一下攪拌一體機維修保養小常識都有哪些內容？
The running in maintenance of the new machine is very key, which can prolong the service life of the machine and reduce the occurrence of small faults. Today, I'll take you to see what are the general knowledge of the maintenance of the integrated mixing machine?
1、詳細閱讀說明書，嚴格按照說明書進行操作保養。
1. Read the instructions carefully and operate and maintain in strict accordance with the instructions.
2、機器發動前繞車一周，檢查油料/冷卻液是否有缺失，輪胎氣壓新機器的走合保養是非常關鍵的，能延長機器的使用壽命，減少小故障的發生，今天小編帶大家來看一下攪拌車維修保養小常識都有哪些內容？
2. Before starting the machine, go around the car and check whether there is any loss of oil / coolant. The running in maintenance of the new machine is very key. It can prolong the service life of the machine and reduce the occurrence of minor faults. Today, I'll take you to see what are the common sense of mixer maintenance?
1、詳細閱讀說明書，嚴格按照說明書進行操作保養。
1. Read the instructions carefully and operate and maintain in strict accordance with the instructions.
2、機器發動前繞車一周，檢查油料/冷卻液是否有缺失，輪胎氣壓及一些關鍵部位的螺栓松緊度，如傳動軸,輪輞處的螺栓。
2. Before starting the machine, go around and check whether the oil / coolant is missing, the tire pressure and the bolt tightness of some key parts, such as the bolts at the transmission shaft and rim.
3、機器啟動后怠速運轉3-5分鐘（尤其是冬天寒冷地區），熄火時同樣操作。
3. After the machine is started, operate at idle speed for 3-5 minutes (especially in cold areas in winter), and do the same when the engine is turned off.
4、新車走合期間，機器不能過載，保證機器輸出功率不超過額定功率的70，否則會導致早期故障的出現（如三漏）。
4. During the running in of the new car, the machine shall not be overloaded to ensure that the output power of the machine does not exceed 70 of the rated power, otherwise it will lead to early faults (such as three leaks).
5、各個檔位都要走合。
5. All gears shall be engaged.
6、操作期間注意儀表盤儀表的指示，確保整機在規定的范圍內工作，如果儀表出現異常，請立即停機檢查。
6. Pay attention to the instructions of the instrument panel during operation to ensure that the whole machine works within the specified range. If the instrument is abnormal, please stop the machine immediately for inspection.
7、注意關鍵部件的溫度，如橋/箱等，若出現高溫現象，立即停機檢查。
7. Pay attention to the temperature of key components, such as bridge / box. In case of high temperature, stop the machine immediately for inspection.
8、走合結束后，將關鍵部位的螺栓全部檢查，包括驅動橋/發動機/變速箱固定螺栓，傳動軸螺栓等螺栓的禁錮情況。
8. After running in, check all bolts at key parts, including the confinement of fixing bolts of drive axle / engine / gearbox and transmission shaft bolts.
9、走合結束，根據操作保養手冊規定，更換油料及濾芯。
9. After running in, replace the oil and filter element according to the provisions of the operation and maintenance manual.
走合結束后，除了根據操保手冊的規定進行定期保養外，也要注意以下幾點：
After running in, in addition to regular maintenance according to the provisions of the operation and maintenance manual, pay attention to the following points:
1、一定用規定的潤滑油及濾芯，否則會降低機器的使用壽命。
1. The specified lubricating oil and filter element must be used, otherwise the service life of the machine will be reduced.
2、不同季節用不同型號的油料。
2. Different types of oil are used in different seasons.
3、不同型號或同型號不同品牌的油或制動液不能混用。
3. Oil or brake fluid of different models or different brands of the same model shall not be mixed.
4、不能對機器進行私自改裝，那樣廠家將不會提供三包。及一些關鍵部位的螺栓松緊度，如傳動軸,輪輞處的螺栓。
4. The machine cannot be modified without permission, so the manufacturer will not provide three guarantees. And the bolt tightness of some key parts, such as the bolts at the transmission shaft and rim.
3、機器啟動后怠速運轉3-5分鐘（尤其是冬天寒冷地區），熄火時同樣操作。
3. After the machine is started, operate at idle speed for 3-5 minutes (especially in cold areas in winter), and do the same when the engine is turned off.
4、新車走合期間，機器不能過載，保證機器輸出功率不超過額定功率的70，否則會導致早期故障的出現（如三漏）。
4. During the running in of the new car, the machine shall not be overloaded to ensure that the output power of the machine does not exceed 70 of the rated power, otherwise it will lead to early faults (such as three leaks).
5、各個檔位都要走合。
5. All gears shall be engaged.
6、操作期間注意儀表盤儀表的指示，確保整機在規定的范圍內工作，如果儀表出現異常，請立即停機檢查。
6. Pay attention to the instructions of the instrument panel during operation to ensure that the whole machine works within the specified range. If the instrument is abnormal, please stop the machine immediately for inspection.
7、注意關鍵部件的溫度，如橋/箱等，若出現高溫現象，立即停機檢查。
7. Pay attention to the temperature of key components, such as bridge / box. In case of high temperature, stop the machine immediately for inspection.
8、走合結束后，將關鍵部位的螺栓全部檢查，包括驅動橋/發動機/變速箱固定螺栓，傳動軸螺栓等螺栓的禁錮情況。
8. After running in, check all bolts at key parts, including the confinement of fixing bolts of drive axle / engine / gearbox and transmission shaft bolts.
9、走合結束，根據操作保養手冊規定，更換油料及濾芯。
9. After running in, replace the oil and filter element according to the provisions of the operation and maintenance manual.
走合結束后，除了根據操保手冊的規定進行定期保養外，也要注意以下幾點：
After running in, in addition to regular maintenance according to the provisions of the operation and maintenance manual, pay attention to the following points:
1、一定用規定的潤滑油及濾芯，否則會降低機器的使用壽命。
1. The specified lubricating oil and filter element must be used, otherwise the service life of the machine will be reduced.
2、不同季節用不同型號的油料。
2. Different types of oil are used in different seasons.
3、不同型號或同型號不同品牌的油或制動液不能混用。
3. Oil or brake fluid of different models or different brands of the same model shall not be mixed.
4、不能對機器進行私自改裝，那樣廠家將不會提供三包。
4. The machine cannot be modified without permission, so the manufacturer will not provide three guarantees.
山汽官方微信
2022-12-23
首頁
產品
電話
置頂