久久综合给合久久狠狠狠97色69,国产欧美在线观看不卡,少妇高潮流白浆在线观看,亚洲熟女精品中文字幕

山東山汽工程機械（集團）有限公司
熱線電話：400-879-1999 山汽官方微信
鄭重聲明 購機 售后
在線詢價
熱線電話：400-879-1999
您現在所在的位置: 首頁> 常見問題

自上料攪拌車安裝與拆卸過程的注意事項

所屬分類：常見問題 發布時間：2022-09-28 來源：http://www.ksmayo.cn 瀏覽量：0

自上料攪拌車軸承的安裝、拆卸方法，應根據軸承的結構、尺寸大小和與軸承部件的配合性質而定。安裝、拆卸的壓力應直接加在緊配合的檔圈端面上，不能通過滾動體傳遞壓力。
The installation and removal method of the bearing of the self feeding mixer truck shall be determined according to the structure, size and matching nature of the bearing. The installation and removal pressure shall be directly applied to the end face of the tight fitting retainer ring, and the pressure shall not be transmitted through the rolling element.
因為這樣會在軸承工作表面造成壓痕，影響軸承正常工作，甚至會使軸承損壞。軸承的保持架、密封圈、防塵蓋等零件很容易變形，安裝或拆卸軸承的壓力不能加在這些零件上。自上料攪拌車生產廠家
This will cause indentation on the working surface of the bearing, affect the normal operation of the bearing, and even damage the bearing. The cage, seal ring, dust cover and other parts of the bearing are easy to deform, and the pressure for installing or disassembling the bearing cannot be applied to these parts. From the manufacturer of charging mixer truck
軸承內圈與軸是緊配合，外圈與殼體為較松配合，可用壓力機將軸承先壓裝在軸承上，然后將軸連同軸承一起裝入殼體中，壓裝時在軸承端面上墊一軟金屬材料的裝配套管（銅的或軟鋼管）。
The inner ring of the bearing is closely fitted with the shaft, and the outer ring is loosely fitted with the housing. Press the bearing onto the bearing with a press, and then install the shaft and the bearing into the housing. When pressing, pad a soft metal assembly sleeve (copper or soft steel pipe) on the end face of the bearing.
自上料攪拌車廠家認為，軸承內圈與軸，外圈與殼體孔都是緊配合，裝配套管端面應做成能同時壓緊軸承內外套圈端面的圓環，或用一圓盤和裝配套管，使壓力同時傳到內外圈上，把軸承壓入軸上和殼體中。此種安裝方法特別適用于能自動調心的向心球面軸承的安裝。
According to the manufacturer of the loading mixer truck, the inner ring of the bearing and the shaft, and the outer ring and the housing hole are closely matched. The end face of the assembly sleeve should be made into a ring that can compress the end face of the inner and outer rings of the bearing at the same time, or a disc and the assembly sleeve should be used to make the pressure transfer to the inner and outer rings at the same time, so as to press the shaft into the shaft and the housing. This installation method is especially suitable for the installation of radial spherical bearing with automatic centering.

 

首頁 產品 電話 置頂